Forum FAQForum FAQSearchSearch MemberlistMemberlist Forum ignore listForum ignore list RegisterRegister ProfileProfile Log in to check your private messagesLog in to check your private messages Log inLog in
Corel X3 pitanje

 
Post new topic   Reply to topic    mi3dot.org Forum Index -> Vektor
View previous topic :: View next topic  
Author Message
Koshpa



Joined: 06 Apr 2009
Posts: 68

PostPosted: 09.09.2009 01:16    Post subject: Corel X3 pitanje Add user to your forum ignore list Reply with quote

Dal netko zna kako u Corelu primjeniti transparency alat vise puta na istom objektu. Primjerice zelim da mi jedan transparency djeluje na donji desni ugao objekta, a drugi sa drugacijim postavkama, na gornji lijevi ugao tog istog objekta? Da li je to uopce moguce u Corelu?
Back to top
View user's profile Send private message
adam|bar



Joined: 28 Jun 2005
Posts: 155
Location: Zagreb

PostPosted: 09.09.2009 03:08    Post subject: Add user to your forum ignore list Reply with quote

Mislim da se ne moze. Osim ako prebacis u bitmap.
Dakle objektu na koji zelis primijeniti vise nivoa transparentnosti stavis prvu transparentnost i onda ga pretvoris u bitmap. E onda na bitmap napravis drugu transparentnost.

_________________
adam baričević online portfolio: http://www.adambar.com
Gettin there is half the fun. Being there is all of it.
Back to top
View user's profile Send private message Visit poster's website
Koshpa



Joined: 06 Apr 2009
Posts: 68

PostPosted: 09.09.2009 09:09    Post subject: Add user to your forum ignore list Reply with quote

A sta ako mi taj objekt vec je bitmap? Confused
Back to top
View user's profile Send private message
adam|bar



Joined: 28 Jun 2005
Posts: 155
Location: Zagreb

PostPosted: 09.09.2009 11:10    Post subject: Add user to your forum ignore list Reply with quote

Pa to nema veze. Jos jednom u Corel-u napraviš "Convert To bitmap". Bez obzira što vec je bitmap.

_________________
adam baričević online portfolio: http://www.adambar.com
Gettin there is half the fun. Being there is all of it.
Back to top
View user's profile Send private message Visit poster's website
Koshpa



Joined: 06 Apr 2009
Posts: 68

PostPosted: 09.09.2009 23:25    Post subject: Add user to your forum ignore list Reply with quote

Ok, thanx! Smile
Back to top
View user's profile Send private message
adam|bar



Joined: 28 Jun 2005
Posts: 155
Location: Zagreb

PostPosted: 09.09.2009 23:32    Post subject: Add user to your forum ignore list Reply with quote

NP

_________________
adam baričević online portfolio: http://www.adambar.com
Gettin there is half the fun. Being there is all of it.
Back to top
View user's profile Send private message Visit poster's website
Adi



Joined: 19 Dec 2005
Posts: 543
Location: Bihac

PostPosted: 10.09.2009 01:32    Post subject: Add user to your forum ignore list Reply with quote

Postoji jedna solucija ako želiš zadržati vektorski objekat, a to je dodavanje još jedne tačke transparencije ili njih više na sami pravac/liniju providnosti.
U toolboxu "Interactive transparency tool", potom uradiš prvu transparenciju po želji, a onda prevuci recimo crnu boju sa palete direktno na istačkanu liniju transparencije i edituj njenu providnost po želji.
U "Transparency type" meniju mijenjaš tip providnosti (Linear, Radial itd.), ako baš ne želiš da ti sve bude pravolinijski i sl.
Nije potpuna sloboda, ali je i dalje vektor Smile
Back to top
View user's profile Send private message Visit poster's website Twitter profile
Display posts from previous:   
Post new topic   Reply to topic    mi3dot.org Forum Index -> Vektor All times are GMT + 1 Hour
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group